【coolzhi】 在 https://github.com/istoreos/istoreos/issues/1275 发布：
反馈bug/问题模板，提建议请删除
1.关于你要提交的问题
为避免重复issue，请先搜索issue，确认没有类似issue再提交新issue；
注意搜索时包括已关闭的issue（删掉搜索框的的“is:open”条件）；
Q：是否用关键词搜索了issue? (使用 “x” 选择)
- 没有类似的issue
2. 详细叙述
(1) 具体问题
1000M带宽
内网测速（局域网传输用那个HOMEBOX插件测试）没问题，
外网测速 用路由器自身跑speedtest可以跑满
局域网设备 跑外网只能跑到500M左右
换回22.3.5最后一个版本 速度正常
A：
(2) 路由器型号和固件版本
A：CPU N3700/网卡8169吧还是啥 不会看
(3) 详细日志和/或截图
下面是网卡信息
A：root@ZHIHOME:~# dmesg | grep -i eth
[ 6.398720] igb: Intel(R) Gigabit Ethernet Network Driver
[ 14.756165] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 14.772410] i40e: Intel(R) Ethernet Connection XL710 Network Driver
[ 14.776129] Intel(R) 2.5G Ethernet Linux Driver
[ 14.805043] r8169 0000:01:00.0 eth0: RTL8168evl/8111evl, 00:e0:4c:69:08:41, XID 2c9, IRQ 121
[ 14.805063] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[ 14.832776] r8169 0000:02:00.0 eth1: RTL8168evl/8111evl, 00:e0:4c:69:08:42, XID 2c9, IRQ 122
[ 14.832796] r8169 0000:02:00.0 eth1: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[ 14.859044] r8169 0000:03:00.0 eth2: RTL8168evl/8111evl, 00:e0:4c:69:08:43, XID 2c9, IRQ 123
[ 14.859060] r8169 0000:03:00.0 eth2: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[ 14.886335] r8169 0000:04:00.0 eth3: RTL8168evl/8111evl, 00:e0:4c:69:08:44, XID 2c9, IRQ 124
[ 14.886354] r8169 0000:04:00.0 eth3: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[ 15.043626] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 15.761301] iavf: Intel(R) Ethernet Adaptive Virtual Function Network Driver
[ 15.765516] usbcore: registered new interface driver ipheth
[ 15.865165] usbcore: registered new interface driver kaweth
[ 16.230044] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 16.660734] usbcore: registered new interface driver cdc_ether
[ 16.736135] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 23.261692] RTL8211E Gigabit Ethernet r8169-0-200:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=r8169-0-200:00, irq=IGNORE)
[ 23.624346] r8169 0000:02:00.0 eth1: No native access to PCI extended config space, falling back to CSI
[ 23.626679] r8169 0000:02:00.0 eth1: Link is Down
[ 23.626722] br-lan: port 1(eth1) entered blocking state
[ 23.626760] br-lan: port 1(eth1) entered disabled state
[ 23.627132] device eth1 entered promiscuous mode
[ 23.630209] br-lan: port 1(eth1) entered blocking state
[ 23.630245] br-lan: port 1(eth1) entered forwarding state
[ 23.638668] RTL8211E Gigabit Ethernet r8169-0-300:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=r8169-0-300:00, irq=IGNORE)
[ 23.957032] r8169 0000:03:00.0 eth2: Link is Down
[ 23.957150] br-lan: port 2(eth2) entered blocking state
[ 23.957171] br-lan: port 2(eth2) entered disabled state
[ 23.957527] device eth2 entered promiscuous mode
[ 23.957733] br-lan: port 2(eth2) entered blocking state
[ 23.957763] br-lan: port 2(eth2) entered forwarding state
[ 23.963509] RTL8211E Gigabit Ethernet r8169-0-400:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=r8169-0-400:00, irq=IGNORE)
[ 24.296112] br-lan: port 1(eth1) entered disabled state
[ 24.297824] br-lan: port 2(eth2) entered disabled state
[ 24.298441] r8169 0000:04:00.0 eth3: Link is Down
[ 24.298953] br-lan: port 3(eth3) entered blocking state
[ 24.298990] br-lan: port 3(eth3) entered disabled state
[ 24.299241] device eth3 entered promiscuous mode
[ 24.311317] RTL8211E Gigabit Ethernet r8169-0-100:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=r8169-0-100:00, irq=IGNORE)
[ 24.669235] r8169 0000:01:00.0 eth0: Link is Down
[ 25.875571] r8169 0000:02:00.0 eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 25.875627] br-lan: port 1(eth1) entered blocking state
[ 25.875643] br-lan: port 1(eth1) entered forwarding state
[ 26.657805] r8169 0000:04:00.0 eth3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 26.657847] br-lan: port 3(eth3) entered blocking state
[ 26.657854] br-lan: port 3(eth3) entered forwarding state
[ 27.005215] r8169 0000:01:00.0 eth0: Link is Up - 1Gbps/Full - flow control off
[ 27.005259] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 264.605473] r8169 0000:03:00.0 eth2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 264.605542] br-lan: port 2(eth2) entered blocking state
[ 264.605564] br-lan: port 2(eth2) entered forwarding state